Download full document:

ipv6

Configuration for ip v6 resource.

Properties

(click to see Operations)

Name	Data Type	Permissions	Description
ralearning	<String>	Read-write	Enable the NetScaler appliance to learn about various routes from Router Advertisement (RA) and Router Solicitation (RS) messages sent by the routers.<br>Default value: DISABLED<br>Possible values = ENABLED, DISABLED
routerredirection	<String>	Read-write	Enable the NetScaler appliance to do Router Redirection.<br>Default value: DISABLED<br>Possible values = ENABLED, DISABLED
ndbasereachtime	<Double>	Read-write	Base reachable time of the Neighbor Discovery (ND6) protocol. The time, in milliseconds, that the NetScaler appliance assumes an adjacent device is reachable after receiving a reachability confirmation.<br>Default value: 30000<br>Minimum value = 1
ndretransmissiontime	<Double>	Read-write	Retransmission time of the Neighbor Discovery (ND6) protocol. The time, in milliseconds, between retransmitted Neighbor Solicitation (NS) messages, to an adjacent device.<br>Default value: 1000<br>Minimum value = 1
natprefix	<String>	Read-write	Prefix used for translating packets from private IPv6 servers to IPv4 packets. This prefix has a length of 96 bits (128-32 = 96). The IPv6 servers embed the destination IP address of the IPv4 servers or hosts in the last 32 bits of the destination IP address field of the IPv6 packets. The first 96 bits of the destination IP address field are set as the IPv6 NAT prefix. IPv6 packets addressed to this prefix have to be routed to the NetScaler appliance to ensure that the IPv6-IPv4 translation is done by the appliance.
td	<Double>	Read-write	Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0.<br>Minimum value = 0<br>Maximum value = 4094
dodad	<String>	Read-write	Enable the NetScaler appliance to do Duplicate Address Detection (DAD) for all the NetScaler owned IPv6 addresses regardless of whether they are obtained through stateless auto configuration, DHCPv6, or manual configuration.<br>Default value: DISABLED<br>Possible values = ENABLED, DISABLED
basereachtime	<Integer>	Read-only	ND6 base reachable time (ms).
reachtime	<Integer>	Read-only	ND6 computed reachable time (ms).
ndreachtime	<Double>	Read-only	ND6 computed reachable time (ms).
retransmissiontime	<Integer>	Read-only	ND6 retransmission time (ms).
__count	<Double>	Read-only	count parameter

Operations

(click to see Properties)

UPDATE | UNSET | GET (ALL) | GET | COUNT

Some options that you can use for each operations:

Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the "warning" query parameter as "yes". For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:
http://<netscaler-ip-address>/nitro/v1/config/login?warning=yes
If any, the warnings are displayed in the response payload with the HTTP code "209 X-NITRO-WARNING".
Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,
To do this, you must specify the username and password in the request header of the NITRO request as follows:
X-NITRO-USER:<username>
X-NITRO-PASS:<password>
Note: In such cases, make sure that the request header DOES not include the following:
Cookie:NITRO_AUTH_TOKEN=<tokenvalue>

Note:

Mandatory parameters are marked in red and placeholder content is marked in <green>.

update

URL: http://<NSIP>/nitro/v1/config/

HTTP Method: PUT

Request Payload:

{
"params": {
      "warning":<String_value>,
      "onerror":<String_value>"
},
sessionid":"##sessionid",
"ipv6":{
      "ralearning":<String_value>,
      "routerredirection":<String_value>,
      "ndbasereachtime":<Double_value>,
      "ndretransmissiontime":<Double_value>,
      "natprefix":<String_value>,
                  "td":<Double_value>,
      "dodad":<String_value>,
}}

Response Payload:

{ "errorcode": 0, "message": "Done", "severity": }

unset

URL: http://<NSIP>/nitro/v1/config/

HTTP Method: POST

Request Payload:

object={
"params":{
      "warning":<String_value>,
      "onerror":<String_value>,
      "action":"unset"
},
"sessionid":"##sessionid",
"ipv6":{
      "ralearning":true,
      "routerredirection":true,
      "ndbasereachtime":true,
      "ndretransmissiontime":true,
      "natprefix":true,
                  "td":<Double_value>,
      "dodad":true,
}}

Response Payload:

{ "errorcode": 0, "message": "Done", "severity": }

get (all)

URL: http://<NSIP>/nitro/v1/config/ipv6

Query-parameters:

filter

http://<NSIP>/nitro/v1/config/ipv6?filter=property-name1:property-val1,property-name2:property-val2

Use this query-parameter to get the filtered set of ipv6 resources configured on NetScaler.Filtering can be done on any of the properties of the resource.

view

http://<NS_IP>/nitro/v1/config/ipv6?view=summary

Use this query-parameter to get the summary output of ipv6 resources configured on NetScaler.

pagesize=#no;pageno=#no

http://<NS_IP>/nitro/v1/config/ipv6?pagesize=#no;pageno=#no

Use this query-parameter to get the ipv6 resources in chunks.

warning

http://<NS_IP>/nitro/v1/config/ipv6?warning=yes

Use this query parameter to get warnings in nitro response. If this field is set to YES, warning message will be sent in 'message' field and 'WARNING' value is set in severity field of the response in case there is a

HTTP Method: GET

Response Payload:

{ "errorcode": 0, "message": "Done", "severity": <String_value>, "ipv6": [ {
      "td":<Double_value>,
      "ralearning":<String_value>,
      "routerredirection":<String_value>,
      "basereachtime":<Integer_value>,
      "ndbasereachtime":<Double_value>,
      "reachtime":<Integer_value>,
      "ndreachtime":<Double_value>,
      "retransmissiontime":<Integer_value>,
      "ndretransmissiontime":<Double_value>,
      "natprefix":<String_value>,
      "dodad":<String_value>

}]}

get

URL: http://<NS_IP>/nitro/v1/config/ipv6/td_value<Double>

HTTP Method: GET

Response Payload:

{ "errorcode": 0, "message": "Done", "ipv6": [ {
      "td":<Double_value>,
      "ralearning":<String_value>,
      "routerredirection":<String_value>,
      "basereachtime":<Integer_value>,
      "ndbasereachtime":<Double_value>,
      "reachtime":<Integer_value>,
      "ndreachtime":<Double_value>,
      "retransmissiontime":<Integer_value>,
      "ndretransmissiontime":<Double_value>,
      "natprefix":<String_value>,
      "dodad":<String_value>

}]}

count

URL: http://<NS_IP>/nitro/v1/config/ipv6?count=yes

HTTP Method: GET

Response Payload:

{ "errorcode": 0, "message": "Done",ipv6: [ { "__count": "#no"} ] }