nsip6¶

Configuration for ip6 resource.

Properties¶

(click to see Operations )

Name	Data Type	Permissions	Description
ipv6address	<String>	Read-write	IPv6 address to create on the Citrix ADC. Minimum length = 1
scope	<String>	Read-write	Scope of the IPv6 address to be created. Cannot be changed after the IP address is created. Default value: global Possible values = global, link-local
type	<String>	Read-write	Type of IP address to be created on the Citrix ADC. Cannot be changed after the IP address is created. Default value: SNIP Possible values = NSIP, VIP, SNIP, GSLBsiteIP, ADNSsvcIP, RADIUSListenersvcIP, CLIP
vlan	<Double>	Read-write	The VLAN number. Default value: 0 Minimum value = 0 Maximum value = 4094
nd	<String>	Read-write	Respond to Neighbor Discovery (ND) requests for this IP address. Default value: ENABLED Possible values = ENABLED, DISABLED
icmp	<String>	Read-write	Respond to ICMP requests for this IP address. Default value: ENABLED Possible values = ENABLED, DISABLED
vserver	<String>	Read-write	Enable or disable the state of all the virtual servers associated with this VIP6 address. Default value: ENABLED Possible values = ENABLED, DISABLED
telnet	<String>	Read-write	Allow Telnet access to this IP address. Default value: ENABLED Possible values = ENABLED, DISABLED
ftp	<String>	Read-write	Allow File Transfer Protocol (FTP) access to this IP address. Default value: ENABLED Possible values = ENABLED, DISABLED
gui	<String>	Read-write	Allow graphical user interface (GUI) access to this IP address. Default value: ENABLED Possible values = ENABLED, SECUREONLY, DISABLED
ssh	<String>	Read-write	Allow secure Shell (SSH) access to this IP address. Default value: ENABLED Possible values = ENABLED, DISABLED
snmp	<String>	Read-write	Allow Simple Network Management Protocol (SNMP) access to this IP address. Default value: ENABLED Possible values = ENABLED, DISABLED
mgmtaccess	<String>	Read-write	Allow access to management applications on this IP address. Default value: DISABLED Possible values = ENABLED, DISABLED
restrictaccess	<String>	Read-write	Block access to nonmanagement applications on this IP address. This option is applicable forMIP6s, SNIP6s, and NSIP6s, and is disabled by default. Nonmanagement applications can run on the underlying Citrix ADC Free BSD operating system. Default value: DISABLED Possible values = ENABLED, DISABLED
dynamicrouting	<String>	Read-write	Allow dynamic routing on this IP address. Specific to Subnet IPv6 (SNIP6) address. Default value: DISABLED Possible values = ENABLED, DISABLED
decrementhoplimit	<String>	Read-write	Decrement Hop Limit by 1 when ENABLED.This setting is applicable only for UDP traffic. Default value: DISABLED Possible values = ENABLED, DISABLED
hostroute	<String>	Read-write	Option to push the VIP6 to ZebOS routing table for Kernel route redistribution through dynamic routing protocols. Possible values = ENABLED, DISABLED
advertiseondefaultpartition	<String>	Read-write	Advertise VIPs from Shared VLAN on Default Partition. Default value: DISABLED Possible values = ENABLED, DISABLED
networkroute	<String>	Read-write	Option to push the SNIP6 subnet to ZebOS routing table for Kernel route redistribution through dynamic routing protocol. Possible values = ENABLED, DISABLED
tag	<Double>	Read-write	Tag value for the network/host route associated with this IP. Default value: 0
ip6hostrtgw	<String>	Read-write	IPv6 address of the gateway for the route. If Gateway is not set, VIP uses :: as the gateway. Default value: 0
metric	<Integer>	Read-write	Integer value to add to or subtract from the cost of the route advertised for the VIP6 address. Minimum value = -16777215
vserverrhilevel	<String>	Read-write	Advertise or do not advertise the route for the Virtual IP (VIP6) address on the basis of the state of the virtual servers associated with that VIP6. * NONE - Advertise the route for the VIP6 address, irrespective of the state of the virtual servers associated with the address. * ONE VSERVER - Advertise the route for the VIP6 address if at least one of the associated virtual servers is in UP state. * ALL VSERVER - Advertise the route for the VIP6 address if all of the associated virtual servers are in UP state. * VSVR_CNTRLD. Advertise the route for the VIP address according to the RHIstate (RHI STATE) parameter setting on all the associated virtual servers of the VIP address along with their states. When Vserver RHI Level (RHI) parameter is set to VSVR_CNTRLD, the following are different RHI behaviors for the VIP address on the basis of RHIstate (RHI STATE) settings on the virtual servers associated with the VIP address: * If you set RHI STATE to PASSIVE on all virtual servers, the Citrix ADC always advertises the route for the VIP address. * If you set RHI STATE to ACTIVE on all virtual servers, the Citrix ADC advertises the route for the VIP address if at least one of the associated virtual servers is in UP state. *If you set RHI STATE to ACTIVE on some and PASSIVE on others, the Citrix ADC advertises the route for the VIP address if at least one of the associated virtual servers, whose RHI STATE set to ACTIVE, is in UP state. Default value: ONE_VSERVER Possible values = ONE_VSERVER, ALL_VSERVERS, NONE, VSVR_CNTRLD
ospf6lsatype	<String>	Read-write	Type of LSAs to be used by the IPv6 OSPF protocol, running on the Citrix ADC, for advertising the route for the VIP6 address. Default value: EXTERNAL Possible values = INTRA_AREA, EXTERNAL
ospfarea	<Double>	Read-write	ID of the area in which the Intra-Area-Prefix LSAs are to be advertised for the VIP6 address by the IPv6 OSPF protocol running on the Citrix ADC. When ospfArea is not set, VIP6 is advertised on all areas. Default value: -1 Minimum value = 0 Maximum value = 4294967294LU
state	<String>	Read-write	Enable or disable the IP address. Default value: ENABLED Possible values = DISABLED, ENABLED
map	<String>	Read-write	Mapped IPV4 address for the IPV6 address.
vrid6	<Double>	Read-write	A positive integer that uniquely identifies a VMAC address for binding to this VIP address. This binding is used to set up Citrix ADCs in an active-active configuration using VRRP. Minimum value = 1 Maximum value = 255
ownernode	<Double>	Read-write	ID of the cluster node for which you are adding the IP address. Must be used if you want the IP address to be active only on the specific node. Can be configured only through the cluster IP address. Cannot be changed after the IP address is created. Default value: 255
ownerdownresponse	<String>	Read-write	in cluster system, if the owner node is down, whether should it respond to icmp/arp. Default value: YES Possible values = YES, NO
td	<Double>	Read-write	Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0. Minimum value = 0 Maximum value = 4094
ndowner	<Double>	Read-write	NdOwner in Cluster for VIPS and Striped SNIPS. Default value: 255
iptype	<String[]>	Read-only	The type of the IPv6 address. Possible values = NSIP, VIP, SNIP, GSLBsiteIP, ADNSsvcIP, RADIUSListenersvcIP, CLIP
curstate	<String>	Read-only	Current state of this IP. Default value: ENABLED Possible values = DISABLED, ENABLED
viprtadv2bsd	<Boolean>	Read-only	Whether this route is advertised to FreeBSD.
vipvsercount	<Double>	Read-only	Number of vservers bound to this VIP.
vipvserdowncount	<Double>	Read-only	Number of vservers bound to this VIP, which are down.
systemtype	<String>	Read-only	The type of the System. Possible Values: Standalone, HA, Cluster. Used for display purpose. Possible values = Stand-alone, HA, Cluster
operationalndowner	<Double>	Read-only	Operational ND6 Owner.
__count	<Double>	Read-only	count parameter

Operations¶

(click to see Properties )

ADD
DELETE
UPDATE
UNSET
GET (ALL)
COUNT

Some options that you can use for each operations:

Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:
http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes
If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.
Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,
To do this, you must specify the username and password in the request header of the NITRO request as follows:
X-NITRO-USER: <username>
X-NITRO-PASS: <password>
Note: In such cases, make sure that the request header DOES not include the following:
Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Note:

Mandatory parameters are marked in red and placeholder content is marked in green

add¶

URL: http:// <netscaler-ip-address> /nitro/v1/config/nsip6

HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"nsip6":{
<b>      "ipv6address":<String_value>,
</b>      "scope":<String_value>,
      "type":<String_value>,
      "vlan":<Double_value>,
      "nd":<String_value>,
      "icmp":<String_value>,
      "vserver":<String_value>,
      "telnet":<String_value>,
      "ftp":<String_value>,
      "gui":<String_value>,
      "ssh":<String_value>,
      "snmp":<String_value>,
      "mgmtaccess":<String_value>,
      "restrictaccess":<String_value>,
      "dynamicrouting":<String_value>,
      "decrementhoplimit":<String_value>,
      "hostroute":<String_value>,
      "advertiseondefaultpartition":<String_value>,
      "networkroute":<String_value>,
      "tag":<Double_value>,
      "ip6hostrtgw":<String_value>,
      "metric":<Integer_value>,
      "vserverrhilevel":<String_value>,
      "ospf6lsatype":<String_value>,
      "ospfarea":<Double_value>,
      "state":<String_value>,
      "map":<String_value>,
      "vrid6":<Double_value>,
      "ownernode":<Double_value>,
      "ownerdownresponse":<String_value>,
      "td":<Double_value>,
      "ndowner":<Double_value>
}}

Response:

HTTP Status Code on Success: 201 Created

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

delete¶

URL: http:// <netscaler-ip-address> /nitro/v1/config/nsip6/ ipv6address_value<String>

Query-parameters:

args=td: <Double_value>

HTTP Method: DELETE

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

update¶

URL: http:// <netscaler-ip-address> /nitro/v1/config/nsip6

HTTP Method: PUT

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"nsip6":{
<b>      "ipv6address":<String_value>,
</b>      "td":<Double_value>,
      "nd":<String_value>,
      "icmp":<String_value>,
      "vserver":<String_value>,
      "telnet":<String_value>,
      "ftp":<String_value>,
      "gui":<String_value>,
      "ssh":<String_value>,
      "snmp":<String_value>,
      "mgmtaccess":<String_value>,
      "ownerdownresponse":<String_value>,
      "restrictaccess":<String_value>,
      "state":<String_value>,
      "map":<String_value>,
      "decrementhoplimit":<String_value>,
      "dynamicrouting":<String_value>,
      "hostroute":<String_value>,
      "advertiseondefaultpartition":<String_value>,
      "networkroute":<String_value>,
      "ip6hostrtgw":<String_value>,
      "metric":<Integer_value>,
      "vserverrhilevel":<String_value>,
      "ospf6lsatype":<String_value>,
      "ospfarea":<Double_value>,
      "tag":<Double_value>,
      "vrid6":<Double_value>,
      "ndowner":<Double_value>
}}

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

unset¶

URL: http:// <netscaler-ip-address> /nitro/v1/config/nsip6? action=unset

HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"nsip6":{
<b>      "ipv6address":<String_value>,
</b>      "td":<Double_value>,
      "ospfarea":true,
      "nd":true,
      "icmp":true,
      "vserver":true,
      "telnet":true,
      "ftp":true,
      "gui":true,
      "ssh":true,
      "snmp":true,
      "mgmtaccess":true,
      "ownerdownresponse":true,
      "restrictaccess":true,
      "state":true,
      "map":true,
      "decrementhoplimit":true,
      "dynamicrouting":true,
      "hostroute":true,
      "advertiseondefaultpartition":true,
      "networkroute":true,
      "ip6hostrtgw":true,
      "metric":true,
      "vserverrhilevel":true,
      "ospf6lsatype":true,
      "tag":true,
      "vrid6":true,
      "ndowner":true
}}

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

get (all)¶

URL: http:// <netscaler-ip-address> /nitro/v1/config/nsip6

Query-parameters:

attrs

http:// <netscaler-ip-address> /nitro/v1/config/nsip6? attrs=property-name1,property-name2

Use this query parameter to specify the resource details that you want to retrieve.

filter

http:// <netscaler-ip-address> /nitro/v1/config/nsip6? filter=property-name1:property-val1,property-name2:property-val2

Use this query-parameter to get the filtered set of nsip6 resources configured on NetScaler.Filtering can be done on any of the properties of the resource.

view

http:// <netscaler-ip-address> /nitro/v1/config/nsip6? view=summary

Use this query-parameter to get the summary output of nsip6 resources configured on NetScaler.

Note: By default, the retrieved results are displayed in detail view (?view=detail).

pagination

http:// <netscaler-ip-address> /nitro/v1/config/nsip6? pagesize=#no;pageno=#no

Use this query-parameter to get the nsip6 resources in chunks.

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "nsip6": [ {
      "ipv6address":<String_value>,
      "td":<Double_value>,
      "scope":<String_value>,
      "type":<String_value>,
      "iptype":<String[]_value>,
      "vlan":<Double_value>,
      "nd":<String_value>,
      "icmp":<String_value>,
      "vserver":<String_value>,
      "telnet":<String_value>,
      "ssh":<String_value>,
      "gui":<String_value>,
      "snmp":<String_value>,
      "ftp":<String_value>,
      "mgmtaccess":<String_value>,
      "restrictaccess":<String_value>,
      "state":<String_value>,
      "curstate":<String_value>,
      "map":<String_value>,
      "decrementhoplimit":<String_value>,
      "dynamicrouting":<String_value>,
      "hostroute":<String_value>,
      "advertiseondefaultpartition":<String_value>,
      "networkroute":<String_value>,
      "tag":<Double_value>,
      "ip6hostrtgw":<String_value>,
      "metric":<Integer_value>,
      "vserverrhilevel":<String_value>,
      "viprtadv2bsd":<Boolean_value>,
      "vipvsercount":<Double_value>,
      "vipvserdowncount":<Double_value>,
      "ospf6lsatype":<String_value>,
      "ospfarea":<Double_value>,
      "ownernode":<Double_value>,
      "vrid6":<Double_value>,
      "ownerdownresponse":<String_value>,
      "systemtype":<String_value>,
      "ndowner":<Double_value>,
      "operationalndowner":<Double_value>
}]}

count¶

URL: http:// <netscaler-ip-address> /nitro/v1/config/nsip6? count=yes

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "nsip6": [ { "__count": "#no"} ] }