l3param¶

Configuration for Layer 3 related parameter resource.

Properties¶

(click to see Operations )

Name	Data Type	Permissions	Description
srcnat	<String>	Read-write	Perform NAT if only the source is in the private network. Default value: ENABLED Possible values = ENABLED, DISABLED
icmpgenratethreshold	<Double>	Read-write	NS generated ICMP pkts per 10ms rate threshold. Default value: 100
overridernat	<String>	Read-write	USNIP/USIP settings override RNAT settings for configured service/virtual server traffic.. . Default value: DISABLED Possible values = ENABLED, DISABLED
dropdfflag	<String>	Read-write	Enable dropping the IP DF flag. Default value: DISABLED Possible values = ENABLED, DISABLED
miproundrobin	<String>	Read-write	Enable round robin usage of mapped IPs. Default value: ENABLED Possible values = ENABLED, DISABLED
externalloopback	<String>	Read-write	Enable external loopback. Default value: DISABLED Possible values = ENABLED, DISABLED
tnlpmtuwoconn	<String>	Read-write	Enable/Disable learning PMTU of IP tunnel when ICMP error does not contain connection information. Default value: ENABLED Possible values = ENABLED, DISABLED
usipserverstraypkt	<String>	Read-write	Enable detection of stray server side pkts in USIP mode. Default value: DISABLED Possible values = ENABLED, DISABLED
forwardicmpfragments	<String>	Read-write	Enable forwarding of ICMP fragments. Default value: DISABLED Possible values = ENABLED, DISABLED
dropipfragments	<String>	Read-write	Enable dropping of IP fragments. Default value: DISABLED Possible values = ENABLED, DISABLED
acllogtime	<Double>	Read-write	Parameter to tune acl logging time. Default value: 5000
implicitaclallow	<String>	Read-write	Do not apply ACLs for internal ports. Default value: ENABLED Possible values = ENABLED, DISABLED
dynamicrouting	<String>	Read-write	Enable/Disable Dynamic routing on partition. This configuration is not applicable to default partition. Default value: DISABLED Possible values = ENABLED, DISABLED
ipv6dynamicrouting	<String>	Read-write	Enable/Disable IPv6 Dynamic routing. Default value: DISABLED Possible values = ENABLED, DISABLED
allowclasseipv4	<String>	Read-write	Enable/Disable IPv4 Class E address clients. Default value: DISABLED Possible values = ENABLED, DISABLED

Operations¶

(click to see Properties )

UPDATE
UNSET
GET (ALL)

Some options that you can use for each operations:

Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:
http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes
If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.
Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,
To do this, you must specify the username and password in the request header of the NITRO request as follows:
X-NITRO-USER: <username>
X-NITRO-PASS: <password>
Note: In such cases, make sure that the request header DOES not include the following:
Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Note:

Mandatory parameters are marked in red and placeholder content is marked in green

update¶

URL: http:// <netscaler-ip-address> /nitro/v1/config/l3param

HTTP Method: PUT

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"l3param":{
      "srcnat":<String_value>,
      "icmpgenratethreshold":<Double_value>,
      "overridernat":<String_value>,
      "dropdfflag":<String_value>,
      "miproundrobin":<String_value>,
      "externalloopback":<String_value>,
      "tnlpmtuwoconn":<String_value>,
      "usipserverstraypkt":<String_value>,
      "forwardicmpfragments":<String_value>,
      "dropipfragments":<String_value>,
      "acllogtime":<Double_value>,
      "implicitaclallow":<String_value>,
      "dynamicrouting":<String_value>,
      "ipv6dynamicrouting":<String_value>,
      "allowclasseipv4":<String_value>
}}

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

unset¶

URL: http:// <netscaler-ip-address> /nitro/v1/config/l3param? action=unset

HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"l3param":{
      "srcnat":true,
      "icmpgenratethreshold":true,
      "overridernat":true,
      "dropdfflag":true,
      "miproundrobin":true,
      "externalloopback":true,
      "tnlpmtuwoconn":true,
      "usipserverstraypkt":true,
      "forwardicmpfragments":true,
      "dropipfragments":true,
      "acllogtime":true,
      "implicitaclallow":true,
      "dynamicrouting":true,
      "ipv6dynamicrouting":true,
      "allowclasseipv4":true
}}

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

get (all)¶

URL: http:// <netscaler-ip-address> /nitro/v1/config/l3param

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "l3param": [ {
      "srcnat":<String_value>,
      "icmpgenratethreshold":<Double_value>,
      "overridernat":<String_value>,
      "dropdfflag":<String_value>,
      "miproundrobin":<String_value>,
      "externalloopback":<String_value>,
      "tnlpmtuwoconn":<String_value>,
      "usipserverstraypkt":<String_value>,
      "forwardicmpfragments":<String_value>,
      "dropipfragments":<String_value>,
      "acllogtime":<Double_value>,
      "implicitaclallow":<String_value>,
      "dynamicrouting":<String_value>,
      "ipv6dynamicrouting":<String_value>,
      "allowclasseipv4":<String_value>
}]}